Class 9 · Data, Protocols and Networks

A protocol is an agreement about what the voltage means. Every fault in this class is two devices that never agreed.

From voltage to meaning#

Everything so far has been about what a voltage is. This class is about what a voltage means, which requires an agreement between two devices about timing, levels and structure.

Strip away the names and there are only a few ideas:

• Serial: send bits one after another down one path. Slower per wire, far fewer wires, and it wins for anything that has to travel.
• Framing: mark where a byte begins and ends, so a receiver that joins late can find its place.
• Differential: send the signal as the difference between two wires so interference cancels, exactly as in balanced audio.
• Addressing: give devices identities so one cable can carry instructions for many.
• Packets: bundle data with a header saying where it is going, so many conversations share one cable.

Every protocol in this class is a specific combination of those five.

Serial, one bit at a time#

Serial, one bit at a time#

The basic asynchronous serial frame is one start bit, then eight data bits, then one or two stop bits. There is no clock line: the receiver knows the agreed bit rate and samples in the middle of each bit, using the start bit's falling edge to synchronise.

That is why both ends must agree on the baud rate, and why a wrong baud rate gives you garbage rather than nothing. The receiver is sampling at the wrong moments and producing bytes that are technically valid and completely meaningless.

Being able to look at a serial line on a scope, measure the width of one bit, and calculate the baud rate from it is a genuinely useful diagnostic skill. One bit of 4 µs is 250,000 baud, which is DMX.

Differential signalling and RS-485#

Differential signalling and RS-485#

Single-ended signalling measures the signal against ground, and over any distance the two ends' grounds are not the same, exactly as in Class 7.

RS-485 sends the signal as the difference between two wires. The receiver looks only at the difference, so induced interference and ground offset cancel. This is what makes 1200 m runs possible in an electrically hostile building.

RS-485 is the electrical layer under DMX512, and the two are constantly confused. RS-485 says what the voltages are; DMX512 says what the bits mean. A DMX problem is nearly always an RS-485 problem, and the RS-485 problems are: no termination, wrong cable impedance, too many devices, a star topology, or a broken screen.

DMX512, in detail#

DMX512, in detail#

DMX512 is a continuously repeated broadcast of 512 bytes, each 0 to 255, sent at 250 kbit/s over RS-485. There is no addressing in the protocol at all: every device receives every byte and picks out the ones starting at the address you set on it.

A packet is:

1. Break — the line held low for at least 92 µs. This is the "new packet starts now" marker, and it is deliberately longer than any valid byte so it cannot be mistaken for data.
2. Mark after break — high for at least 12 µs.
3. Start code — one byte, 0x00 for normal dimmer data.
4. Up to 512 slots — one byte each, each preceded by a start bit and followed by two stop bits.

Each slot takes 44 µs. A full 512-slot packet plus break is about 22.7 ms, which gives a refresh rate of about 44 Hz. Send fewer channels and it refreshes faster, which is why some consoles let you limit the channel count and why a moving light rig can feel more responsive when you do.

DMX512, in detail#

The consequences of "no addressing":

• Two fixtures set to the same address both respond, identically, forever, and nothing reports an error. There is no collision detection because there is no addressing to collide.
• A fixture cannot tell the console anything. DMX is one direction only. Everything you know about the state of the rig, you know because you sent it.
• The 513th byte does not exist. A fixture at address 510 needing 8 channels does not fit, and it will silently use whatever it can and behave strangely.

Topology, termination and reflections#

Topology, termination and reflections#

DMX is a daisy chain, not a star. One cable in, one cable out, device to device, and a terminator at the far end.

The terminator is a 120 Ω resistor across the data pair at the last device. Here is why it matters, and it is the impedance idea from Class 7 arriving in its RF form.

A cable has a characteristic impedance, 110 Ω for DMX cable, set by its physical construction. A signal travelling down it that meets an impedance discontinuity — an open end — reflects, and the reflection travels back and adds to the original. At 250 kbit/s over tens of metres, that reflection arrives during the following bits and corrupts them.

A resistor matching the cable impedance at the far end absorbs the energy instead of reflecting it.

What an unterminated line looks like: it usually works. On a short run, at low channel counts, with a strong transmitter, the reflection is small enough to survive. Then somebody adds twenty metres, or the temperature changes, or a fixture is added, and it becomes intermittent flicker on one fixture in the middle of the run — which is the hardest fault to diagnose, because it appears nowhere near the actual problem.

Topology, termination and reflections#

This is why "it worked without a terminator" is a statement about luck, and it is on the list of sentences a technical director should never accept.

The other rules that follow from RS-485: no more than 32 devices per run without a splitter, no more than about 300 m of cable, never a star split without an active splitter, and microphone cable is not DMX cable — its impedance is nearer 50 Ω and its capacitance is higher, so it is another way of being lucky rather than correct.

The rest of the protocol landscape#

The rest of the protocol landscape#

The two distinctions worth carrying#

State versus event. DMX sends the complete current state, forty-four times a second, forever. If a packet is lost, the next one corrects it. MIDI and OSC send events: "note on", "go". If an event is lost, it is lost, and nothing corrects it.

That single difference decides how each fails. A DMX rig with a marginal cable flickers. A MIDI show control link with a marginal cable misses a cue, and the show is now in the wrong state until somebody intervenes. Event protocols need more reliability than state protocols, not less, and people habitually assume the opposite.

The two distinctions worth carrying#

Unicast, broadcast, multicast. Art-Net commonly broadcasts, which means every device on the network processes every packet whether it needs it or not. sACN uses multicast, where devices subscribe to the universes they want and the switch only sends those. On a large rig this is the difference between a network that works and one that saturates, and it is why sACN has largely won.

The network underneath#

sACN and Art-Net are DMX carried by an ordinary network, which means every network fault is now also a lighting fault. You do not need to be a network engineer, but three ideas stop most of them.

An address and a mask. A device has an address like 10.101.3.42 and a mask like 255.255.255.0, usually written /24. The mask says which part of the address is the neighbourhood and which part is the house. Two devices can only talk directly if their neighbourhood parts match.

That single sentence is the whole of fault 11 in Class 10: a node on 2.0.0.5/8 and a console on 10.101.3.10/24 are in different neighbourhoods, so they cannot reach each other, and both report themselves as perfectly healthy.

Art-Net's historical addresses. Art-Net grew up on 2.x.x.x with a /8 mask, and much equipment still defaults there. sACN does not care and normally uses whatever the venue uses. A rig with both on it needs a deliberate decision rather than two sets of defaults.

Separating traffic. A show network carries control that has a deadline and management traffic that does not. Putting a laptop's software updates on the same VLAN as your lighting is the most common self-inflicted wound in this part of the industry. Separate them physically, or by VLAN, and the sibling module on computer systems and networking is four hours on exactly this.

The network underneath#

RDM: the return path DMX never had#

RDM: the return path DMX never had#

Remote Device Management adds a conversation to a line that was designed to be a monologue. The controller stops transmitting DMX briefly, sends a request, and listens for a reply in the gap.

What it gives you is genuinely transformative on a big rig:

• Discovery. Find every responding device on the line, with its manufacturer, model and serial.
• Addressing. Set a fixture's address and personality from the desk, rather than on a ladder.
• Sensors. Read a fixture's lamp hours, internal temperature and fan status.
• Identify. Make one fixture announce itself, which is how you find the third one on run two.

Three practical constraints, and they are all the same constraint:

Everything in the path must pass it. A splitter that is not RDM-capable blocks the return direction while passing DMX perfectly, so the fixtures work and none of them are discoverable. That is fault-finding misery, because the symptom points at the fixtures and the cause is a box in the middle.

RDM: the return path DMX never had#

It shares the line's time budget. Discovery is chatty, and running it during a show steals slots from the DMX. Discover during the rig check, not during the performance.

Not every fixture implements all of it. The standard is large and support is partial, so a fixture that discovers but will not accept an address change is behaving badly rather than being broken.

At the bench#

Two hours and twenty minutes.

Block A — Read a serial line (35 min)#

Put the scope on a serial line at a known baud rate. Measure one bit's width. Calculate the rate. Confirm against the setting.

Then have your partner change the rate without telling you, and identify the new rate from the scope. Then decode one byte by hand from the trace: find the start bit, read the eight data bits least significant first, and convert to a character.

Slow, and worth doing exactly once, because after it you will never be confused about what serial data physically is.

Block B — Anatomy of a DMX packet (35 min)#

Scope on a live DMX line. Find the break and measure it. Measure the mark after break. Measure one slot. Measure the whole packet and calculate the refresh rate.

Then change the console's channel count from 512 to 64 and measure the refresh rate again. Write down both numbers and the ratio.

Block C — Termination, proved (35 min)#

A 100 m DMX run with a fixture at the far end and one in the middle.

Scope at the far end, terminated: clean. Remove the terminator: photograph the reflection. Measure the amplitude of the ringing and the time between the edge and the reflection, then calculate the cable length from that time and the propagation velocity. It will be close to 100 m, and that calculation is how a real cable fault locator works.

Then substitute microphone cable for the DMX cable and repeat. Note that it may still work, and write one sentence about what that proves and what it does not.

Block D — Address collisions and off-by-one (35 min)#

Patch six fixtures. Introduce, one at a time: two fixtures on the same address, a fixture one channel off, a fixture whose footprint runs past 512, and a fixture on the wrong universe.

For each, write down the symptom as a stage manager would describe it, then the actual cause. That translation, from "the upstage left one is doing something weird" to "an address collision", is the skill.

Numbers from this class#